The pilot is behind a cover plate at the bottom of the heater..
Likewise, people ask, where is the pilot light on a water heater?
How to Light a Water Heater Pilot Light
- Open the door/cover over the pilot light access.
- Use a flashlight or a headlamp to find the burner inside.
- Turn the gas knob to “Pilot,” press and hold it down.
- While still holding the gas down, light that pilot.
- When the flame ignites, continue to hold the gas knob or button down for a full minute.
Also, how do I know if the pilot light is out on my water heater? The pilot gas line is a small metal tube below the burner assembly and distinctive by the slight upturn at the end. It will be apparent, if the pilot is lit, by the small blue flame burning at the end. If you do not see a small blue flame burning, the pilot light is out.
Also to know is, what causes a pilot light to go out on a water heater?
Some of the most common reasons that water heater pilot lights go out include: A faulty thermocouple. Over time, thermocouples can begin to malfunction and shut off the gas supply to the pilot light even if it's burning properly. A bent or dirty thermocouple.
Is it dangerous if the pilot light goes out on water heater?
A device called a thermocouple is heated by the pilot light flame. As long as the thermocouple remains hot, gas is supplied to the pilot light. If the pilot light goes out, the gas is shut off and there is no danger of gas accumulating because the pilot light is out.
Related Question Answers
Why does my pilot light go out when I release the pilot light knob?
The most likely of those is that the thermocouple needs to be replaced. The button you press to light the pilot bypasses the thermocouple. When you release the button, the thermocouple ensures that unburned gas doesn't get released by shutting off the gas when it's not heated by the burning pilot light.How do I reset my water heater?
Part 2 Pressing the Reset Button - Locate the red reset button. There should be a red button in the center of the control panel.
- Press the button firmly. The reset button can sometimes be sticky, especially if you haven't reset the heater in a while.
- Wait to hear the button click.
How much does it cost to replace a thermocouple?
Thermocouple Replacement - $20-$150 Calling a professional plumber to install a new thermocouple should only be up to $150. If you do the work yourself, you will only pay the price of the part which is about $20.Can a pilot light cause carbon monoxide?
Carbon monoxide is a colorless, odorless gas produced during burning fuel. It doesn't leak from a pilot light that's gone out, but if the light keeps going out even after you relight the pilot, it can indicate that you have other problems.How do you know if you have a bad thermocouple?
If you can't get the flame to light at all, and you're sure the gas is on, there's probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that's the sign of a thermocouple malfunction.Will pilot light go out if gas is turned off?
Pilot lights will occasionally go out. Sometimes the cause is easily resolved, such as running out of propane or turning off the gas. However, if the pilot light needs to be relit more than once per season, it should be inspected by a qualified service technician.Is a pilot light always on?
At the same time, that pilot light is burning off the gas and preventing the poisonous fumes from entering your home. Some pilot light tubes have automatic shut-offs if the flame goes out, but not all of them do, so each and every pilot light in the home should be routinely checked to make sure it is always on.Can you clean a thermocouple?
If the Thermocouple is faulty it will cause the unit to shut down. How to clean? Remove Thermocouple from pilot assembly, using steel wool or emery cloth to lightly clean the tip removing any soot or build up that might have accorded due to an improper pilot flame.Do I need to turn off hot water heater if I turn off water?
If the element gets turned on without water surrounding it, it gets too hot and burns up. In rare circumstances, you could also get a buildup of dangerous pressure if the relief valve were to fail. So, yes, please turn off your water heater when you turn off your water main.Why won't my pilot light stay lit on my water heater?
If your gas water heater doesn't stay lit, you may have a defective control thermostat. The gas supply to the pilot assembly is controlled by this valve. If the pilot light won't stay lit and the thermocouple is okay, then the thermostatic control valve may be defective.Should pilot light always be on water heater?
Your water heater does not have an ignitor. The pilot should always be burning on your water heater. Sometimes the pilot flame is hard to see through the viewing window. To be sure if the pilot is on or off, you need to remove the access door and shield and look at the burner and pilot through the opening.How do you clean a thermocouple on a water heater?
Turn off the lever handle gas valve to the water heater and turn the knob on the top of the temperature control valve to “Off.” Use open-end wrenches to unscrew the nuts that connect the burner gas line, the pilot gas line and the thermocouple. Pull the gas tubes and thermocouple down out of the gas valve.Why is my boiler not igniting?
Burner won't ignite: This is the most common cause of a boiler failing to provide heat. If the gas jets on the burner will not ignite, no heat will warm up the water in the tank. The trouble may be due to a failed electronic igniter/pilot light, or perhaps trouble in the gas line.What does a thermocouple look like?
The thermocouple looks like a piece of metal tubing smaller than a soda straw. To find it, first locate the gas control box. This is the box that the main gas line enters, where you turn the gas on in the furnace. The other end of the thermocouple sits in the flame of the pilot light.What happens when a water heater goes out?
POP! Same thing happens to water heaters. If too much pressure builds in the tank, it will eventually spring a leak and burst. Also, if the T&P valve goes bad/starts leaking (which it will eventually), then pressure will continue to build in the tank, leading to a burst or explosion.How do you restart a gas furnace?
Once the gas has had time to dissipate, turn the knob to "Pilot." Then, hold down the "Reset" button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.How do you test a thermocouple?
Turn your multimeter to millivolts to perform an open circuit test. Place one of the test leads of the multimeter on the side of the thermocouple and the other to the end that enters the gas valve. Ignite a lighter, or other heat source with a flame, at the opposite end of the thermocouple.What causes a water heater pilot to go out?
Some of the most common reasons that water heater pilot lights go out include: A faulty thermocouple. Over time, thermocouples can begin to malfunction and shut off the gas supply to the pilot light even if it's burning properly. A bent or dirty thermocouple.Why would a water heater pilot go out?
Usually, a problem with the thermocouple causes the pilot light to go out. The thermocouple is the small copper rod that the pilot light hits. The thermocouple's job is to shut a gas safety valve if the pilot light goes out. That's important because gas is always being supplied to the pilot to keep the flame lit. 
