Look at the bottom of the inside of the dryer. Depending upon your model, your pilot light may be on the right or the left. If you can locate the pulley, the pilot light will be on the opposite side.
.
Then, how do I light the pilot on my gas dryer?
Remove the heat when the pilot lights, but keep the knob depressed for about 20 seconds to give the thermocouple time to heat up. Release the knob and ensure the pilot stays lit, then turn the knob to the "on" position and replace the panel on the front of the dryer. The dryer is now ready to use.
Likewise, what would make a dryer not heat up? Another possible cause for a dryer not heating up could be attributed to a faulty thermal fuse. Once a dryer's thermal fuse has blown, it is no longer of any use. If your dryer's fuse is blown, you will have to replace it.
Likewise, does dryer have pilot light?
Your dryer does not have a pilot light. The dryer has an automatic electronic ignition system. It uses a glow bar ignitor that must glow red hot in order to ignite the gas burner once the gas valve opens.
Does a Maytag gas dryer have a pilot light?
Your dryer does not have a pilot light, it uses an electronic glow bar igniter that glows red hot that ignites the gas. There are several electrical components that must be in working order before the glow bar igniter will be allowed to glow.
Related Question AnswersHow do you know if your dryer is gas?
If you see one cord attached to the dryer, it's electric. If you see a cord and a thin stainless steel connector, your dryer is gas. (Don't confuse the dryer's flexible metal vent tube with the gas connector. The vent tube will be much larger than the gas connector.)Why is there no heat in my dryer?
With an electric clothes dryer, no heat often means that the circuit breaker or fuse that controls the power has blown; reset or replace it. Be aware that a dryer may have two breakers or fuses. The motor will run when one works, but the heating element requires both.Why does it smell like gas in my dryer?
If you smell gas even when your dryer is off, the problem might be a defective valve. The valve should seal shut when your dryer is off so that gas isn't released. However, it's possible for the valve to fail over time and emit a small amount of gas into the air, whether or not the dryer is operating.What is better a gas dryer or an electric dryer?
Electric dryers use heating coils. Gas dryers use a gas burner to create heat and typically cost more in the initial purchase. Another difference in the gas vs. electric dryer debate is that gas dryers tend to run hotter than electric dryers, which means clothes can potentially tumble for a shorter period.Why is my gas dryer not drying my clothes?
Dryer air vent hose clogged with lint. Clean your dryer AIR VENTING HOSE on a yearly basis! It is the reason your dryer takes forever to dry AND can be a fire safety hazard! At times your dryer can overheat and this can cause the motor that turns the drum to stop working temporarily.Why is my gas dryer blowing cold air?
If the air flow in the dryer is restricted, the temperature in the heating chamber can get hot enough to blow the thermal fuse. If the fuse blows, it cuts power to the coils that control the gas valve. The fuse is usually mounted to the exhaust duct just inside the back panel.Do gas dryers have a thermal fuse?
The thermal fuse is a safety device that trips if the air flowing through the dryer begins to overheat. A blocked exhaust vent is the most common reason the air overheats. We also have instructions for replacing the thermal fuse in an electric dryer.Do gas stoves have pilot lights?
Gas stoves today use two basic types of ignition sources, standing pilot and electric. A stove with a standing pilot has a small, continuously burning gas flame (called a pilot light) under the cooktop. Early gas ovens did not have a pilot. One had to light these manually with a match.Does a gas dryer have a heating element?
Natural gas dryers use an electric heating element, known as the igniter, to produce enough heat to light the gas inside the combustion tube. Once you replace the heating element inside the gas dryer, your drying time should shorten tremendously.How long does a gas dryer stay lit?
The flame stays lit for 10 seconds or so and then shuts off.How do you reset a whirlpool gas dryer?
If your Whirlpool dryer displays a "PF" error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing "Start" for a few seconds to restart the dryer. If the dryer does not restart automatically, select a new cycle and any options then press "Start" to begin.Why is my Whirlpool gas dryer not heating?
Dryer heating element. If your dryer does not heat first check for a blown thermal fuse on the blower housing before replacing the heating element. In most cases the heating element will have a break in the element if defective. The thermal fuse is a safety device designed to protect the dryer from overheating.How do you reset a dryer fuse?
How to Reset a Thermal Fuse- Unplug the clothes dryer's power cord from the wall outlet.
- Swing the front panel out towards you so that you can look into the compartment.
- Aim a flashlight at the flat-can-like component to locate the blown thermal fuse.
