What does code e01 mean on Whirlpool washer?

Anonymous User. Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.

Likewise, how do you reset the code on a Whirlpool washer?

Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.

how do you reset a Whirlpool washing machine?

Unplug the washer for 1 minute from the electrical outlet.
Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
The motor has now been reset and is ready for you to start a cycle.

Considering this, how do I reset my Whirlpool Duet washer?

Unplug the washer for 30 seconds to attempt to reset the Duet washer control. if your fill hoses have a flood stop check valve turn the water off, disconnect the hoses and run a little water into a bucket. Then reconnect the hoses to your washer and do a Duet Washer Quick Diagnostic Test.

What does the Code F mean on a Whirlpool washer?

The “F” error code indicates the washing machine system or “Fault”. Ehe “E” error is indicating the part in your washer that causing the issue or “Error”. As a general rule, these “F” error codes mean the following… – Whirlpool Duet Washing Machine F5 error code indicates door lock and door switch issues.

How do I reset my front load washer?

Unplug the washer from the power outlet or turn the circuit breaker to the unit off. With the power disabled, press and hold the START/PAUSE button for 5 seconds. Plug the washer back in, or turn the circuit breaker back on.

What does Code F mean on Whirlpool Duet washer?

The F/dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen. When the door fails to lock, the machine won't run at all.

How do I clear f9 code?

How to Remove the F9 Code From Maytag

Hold on the "Start/Stop" button for 10 seconds. This will end the beeping.
Open the oven door and check the door latch. If it wiggles, it needs to be tightened.
Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch.
Press the oven door shut gently.
Test the oven.

How do you fix the F 28 code on a Whirlpool Duet washer?

How to Fix the F-28 Code on a Whirlpool Duet

Unplug the electrical cord from the wall outlet.
Open the detergent tray on the top of the washer and locate the Phillips screws that hold it in place.
Remove the detergent tray screws using a Phillips screwdriver and pull off the tray.
Find the control console unit reset lever and pull it toward you.

What does f09 mean on a Whirlpool washing machine?

Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.

What does f21 mean?

The Whirlpool washer error code F21 means the washing machine has a “water draining issue”, meaning the drain pump itself, or the drain hose is clogged and the washer is having problems draining the water out.

Do Whirlpool washers have a reset button?

Does a washing machine have a reset button? If it isn't possible to access thewashing machine'splug to manuallyresetthewasher, turn off the circuit breaker. Leave it off from 30 seconds to 1 minute, depending on themachinemodel or instructions in the owner's manual.

How do you unlock a front load washer?

How to Manually Unlock a Kenmore Front Load Washing Machine

Touch "Control Lock" for five seconds until "CL" disappears from the washer's display to unlock the control panel.
Press "Start/Pause" to manually pause the cleaning cycle.
Pull the door's handle to open the door and add or remove the clothing from the washer.

How do I unlock the door on a Whirlpool Duet washer?

How to Unlock a Whirlpool Duet Washing Machine

Reach up inside the front panel and locate the door latch assembly on the right side of door.
Feel for a tear-drop shaped tab on the bottom of the door latch assembly. This tab will manually unlock the door.
Gently pull down on tab about 1/4 inch or until you hear a click. The door should open.

How do you unlock the door on a Whirlpool Duet washer?

Reach through the open panel and up to the door lock. Find the release ring below the locking mechanism. Pull down on the ring to unlock the door. If you must manually unlock the washer door after each wash cycle your drain pump or pressure switch may have failed and would need replacing.

How do I fix my Whirlpool Duet washer?

Whirlpool Duet Washer Door Will Not Unlock

Unplug the washer or disconnect power.
Remove the lower kick panel.
Reach up along the inside of the front and locate the bottom of the door switch/lock unit.
Located on the bottom of the door switch/lock unit is a tear-drop shaped tab.

How do you unlock a Whirlpool front load washer?

Pull down on the bottom panel and pull it away from the washer. Reach through the open panel and up to the door lock. Find the release ring below the locking mechanism. Pull down on the ring to unlock the door.