Manual Control Lighting Instructions
- STOP!
- Make sure the manual shutoff valve is fully open.
- This heater is equipped with an ignition device (piezo) which automatically lights the pilot.
- Push in gas control knob slightly and turn control knob clockwise to the OFF position.
- Wait 5 minutes to clear out any gas.
.
Herein, how do you light a gas log?
You turn the control knob to the pilot position, push the knob in, light the pilot with a match, then hold the knob down for 30 seconds or so until the pilot stays lit by itself. Once the pilot light will stay lit on its own, you can then move the knob to the "On" position.
Furthermore, how can I tell if my gas fireplace is ventless? How to Tell If Your Gas Logs Are Vent-Free
- Inspect the logs. All vent-free logs are firmly attached to a U-shaped burner and cannot be moved.
- Follow the gas line from beneath the logs to where it disappears in the wall or floor. If the gas is merely contained by a simple gas line, then the logs are vent free.
- Turn on the fireplace.
Also to know, how do you light a gas fireplace pilot light?
Hold the gas control button down while you hold the end of a lighted match or lighter at the end of the pilot tube. The pilot should start as soon as the flame is close enough. Hold the pilot button down for about 20 seconds to give the thermocouple time to heat up, then release it. The pilot should stay lit.
How does a ventless gas fireplace work?
Ventless Gas Fireplaces: How They Work Instead of venting through a chimney or tube to the outside, a ventless gas fireplace sends the spent gasses back into the room. Traveling in a U-shaped path, oxygen enters the bottom of the ventless gas fireplace from the room and vents back into the room through the top.
Related Question AnswersHow do you bleed air from gas logs?
While pressing the valve control knob in, press the igniter button repeatedly until the pilot ignites. This could take anywhere from one to 10 minutes to bleed air out of the lines as the gas starts to flow. Once the pilot is lit, continue to press the valve knob inward for 30 seconds before releasing it.Why is my gas fireplace not turning on?
1. Pilot light systems are the most common reason gas fireplaces fail to light, so check the main gas valve to make sure the gas is turned on. If gas is coming out of the pilot, but it still won't light, the spark igniter could be the problem. Look for and clear out any debris between the igniter and thermocouple.How do you clean unvented gas logs?
How to Clean Gas Fireplace Ventless Logs Putting Out Soot- Turn off the gas and electric leading to the fireplace.
- Carefully remove the logs, stones and burner, and place them on a newspaper.
- Attach a hose to the vaccum, and clean the inside of the firebox.
- If doors are attached to your fireplace, clean them inside and out with a non-ammonia cleaner.
How do you turn on a gas fireplace without the key?
When learning how to turn on a gas fireplace without a key, confirm that the unit has a control panel with an igniter switch. Remove any fireplace decoration that's in the way. Control panels can usually be found at or around the base of the fireplace, concealed by a decorative screen that should be moved.How do you start a gas fireplace with a key to the wall?
How to Use a Gas Fireplace With a Key- Look around the base of the fireplace and locate a small metal hole; this is the keyhole.
- Grasp the handle of the key, which looks like a long metal pole.
- Turn the key counterclockwise approximately 1/2 turn to release the flow of gas into the fireplace logs.
Can you light gas logs with a lighter?
Light a match or butane candle lighter and hold it near the burner in the fireplace. Turn the gas key to release gas to the burner. Keep in mind that while gas fireplaces are safe when used properly, you need to turn off the valves and call a professional for help if you notice a heavy smell of gas when its in use.How do you light a pilot light?
Once the gas has had time to dissipate, turn the knob to "Pilot." Then, hold down the "Reset" button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.Are gas fireplaces safe?
Gas fireplaces are safe. But as with all gas appliances, they do produce carbon monoxide. If something goes wrong, carbon monoxide put the home's occupants at risk. Therefore, carbon monoxide detectors are a critical part of gas fireplace safety, even if you don't use the fireplace often.What is a blue flame log lighter?
When the Power Goes Out or anytime, increase heat in wood burning fireplace with the Blue Flame Log Lighter. CSA Certified for use with natural gas, this energy saving Blue Flame Log Lighter ensures safety for the end user by mixing air and gas together for a safer light up. Safely ignites wood logs.Where is the pilot light on gas logs?
With the control knob pushed in, push and release the piezo ignitor button to light the ODS pilot. The pilot is located on the left side of the heater, behind the middle log and on the back of the rear burner. If piezo ignitor does not light the pilot, refer to your manual for Match Lighting Instructions.How do you clean a gas fireplace insert?
Steps- Turn the gas off. Before you begin cleaning your gas fireplace, you must first make sure you turn the gas valve to the “off” position.
- Brush off the gas logs. Remove the gas logs from the fireplace and take them outside for cleaning.
- Vacuum the lava rocks.
